Product
High speed doors are the advantage of fast speed, are installed where space needs to be separated and rapid opening/closing is required. For example, food factories, beverage factories, electronic precision factories, heavy industries, underground parking lots, hotels, etc.
Model | C-1 |
---|---|
Usage | Standard Type |
Benefits | Most popular product line. Equipped with high strength wind-bar, wind-bar locks which prevents separations under high wind conditions. Easy sheet installation makes it efficient to replace individual sheets of damaged sheets caused by vehicles and equipment. Designed for easy exchange between winter and summer sheets |
Model | C-2 |
---|---|
Usage | Slim Type |
Benefits | Motor is installed inside the drum unit which enables to create additional space around the motor unit. Water resistant. Convenient to install in limited spaces such as hallways and walkways |
Model | C-3 |
---|---|
Usage | Self-recovery type |
Benefits | Premium class high speed auto door system. Most popular and designed for high traffic areas. It comes with auto door recovery system which repairs the doors caused by impacts against forklifts and moving equipment. Minimize the repair cost. Suitable for electronics and automotive industry. |
Direct sprocket approach to establish a stable system by separating the drive shafts and the storage shafts that collect the curtains that drive the door curtain.
In the event of a vehicle collision, a PVC rail supporting both door curtains is applied to prevent any deformation or damage in the event of a vehicle collision, and there is no gap between the sheet and the rail to minimize foreign matter or air inflow.
Model | C-4 |
---|---|
Usage | High speed door for Indoor/Lab |
Benefits | Product designed based on C-1 base. Lowered noise level by eliminating wind-bars. Used special high speed motor and reach 3m/s. Can install access card |
Model | C-5 |
---|---|
Usage | High speed door for Clean Room |
Benefits | The premium auto door system designed for clean room areas equipped with various types of sensors. Suitable for the spaces required to build a complete clean environment. Commonly used in conjunction with an air shower. This model is equipped with COAD hermetic seal which provides tight seal. |
Model | C-6 |
---|---|
Usage | High speed door for Car Wash |
Benefits | This high speed model is designed for car wash businesses which have noise, dust & frost problems. Since the model is designed to link with the existing car wash system, it doesn’t require an additional administration. The system can sustain -10 degrees temperature environment. |
Model | C-7 |
---|---|
Usage | High speed door for Hotel parking |
Benefits | This high speed model is designed for motel parking lots. Equipped with LED lighting on the frame which improves the overall appearance of the door and harmonize with motel’s interior design. Auto door also helps to protect motel customers’ privacy. The doors, coated with indestructable Nano Ink which protects the outer materials from UV and water, have semi-permanent life cycle. |
Model | C-8 |
---|---|
Usage | High speed door for Refrigerator/Cold room |
Benefits | This high speed auto door system is designed for refrigerator & freezer units. It can operate at the temperatures between –30℃ ~ +65℃. Airtight sealed and heating hot-wire design ensure the door operate properly at extreme weather conditions. (Exceptional performance under negative/positive pressure) |
Model | C-9 |
---|---|
Usage | High speed door for Food Manufacturer |
Benefits | This high speed auto door system is designed to meet HACCP and GMP requirements for food industry. Equipped with the non-contact sensors and switches to prevent the foreign materials from entering into the system. It is also equipped with the bacteria resistant sheets to blocks the growth of microorganisms. |
Model | C-10 |
---|---|
Usage | High speed door for Big size |
Benefits | This high speed auto door system is designed for harsh environments. It is 10M products which are applied in heavy industries, shipyards and automotive production lines. |
Model | C-11 |
---|---|
Usage | High speed door for Unmanned system |
Benefits | This high speed auto door system is designed for Unmanned system. The door system integrates with management system . Maximize the space utilization which was created by Tuberon Motor. Neat appearance. |
Model | C-12 |
---|---|
Usage | High speed door for Conveyor |
Benefits | This high speed auto door system is designed for conveyer line environments where massive product movements. It is capable to integrate with the overall conveyer system (robots). With a built-in self-recognition program, it supports a seamless logistics system; and, it also provides the safety and security at the same time. |
Model | C-13 |
---|---|
Usage | High speed door for Explosion Proof |
Benefits | This high speed auto door system is designed for the electricity sensitive environments such as paint manufacturing plants and natural gas facilities. Equipped with special flame proof and explosion proof parts to eliminate the risk of explosion. |
C-13 Explosion Proof Model
Model number | Size | M30 (Switch) | #54 (Merer switch unit) |
---|---|---|---|
FOB-1 | 120 x 140 | 1 | 1 |
FOB-2 | 120 x 185 | 2 | 1 |
FOB-3 | 120 x 240 | 3 | 2 |
FOB-4 | 120 x 295 | 4 | 2 |
FOB-5 | 120 x 350 | 5 | 2 |
1. Highly efficient perpendicular shaft speed control: about 20% more efficient compared to a worm gear motor, efficiency rate is 85% or higher.
2. Low noise & low vibration: lower noise and vibration compared to bevel type motors (avg. 52 ~ 65dB)
3. High strength and long life: increased gear strengths and life by using carburized gears.
4. Light weight & optimization: reduced the installation space using offset method; and reduced the weight of the case and the speed control unit.
Worm gear | Hypoid gear | Note | |
---|---|---|---|
Motor volume(kW) | 0.4 | 0.4 | |
Reduction ratio | 10:1 ~ 20:1 | 10:1 ~ 20:1 | |
Efficiency | 60% | 85% | about 25% difference |
Output Torque (kg-m) | 7.8 | 11.0 | about 25% difference |
Size(mm) Including motor | 416x238x195 | 372x132x118 | about 50% difference |
Weight(kgf) Including motor | 20 | 11 | about 50% difference |
1. Boasts the industry’s smallest flange dimensions.
2. Unlike typical concentric shaft gear motor (the output shaft and the motor shaft
oncentric) structure, so it is possible to reduce the flange. In addition to the centers of the motor flange there is no slippage and compact.
3. Decelerate properly on both sides to support a structure, low noise achieved by adopting a number of teeth of the unique dimensions
Worm gear | Hypoid gear | Note | |
---|---|---|---|
Motor volume(kW) | 0.4 | 0.4 | |
Reduction ratio | 10:1 ~ 20:1 | 10:1 ~ 20:1 | |
Efficiency | 60% | 85% | about 25% difference |
Output Torque (kg-m) | 7.8 | 11.0 | about 25% difference |
Size(mm) Including motor | 416x238x195 | 372x132x118 | about 50% difference |
Weight(kgf) Including motor | 20 | 11 | about 50% difference |
1. Highly efficient perpendicular shaft speed control: about 20% more efficient compared to a worm gear motor, efficiency rate is 85% or higher.
2. Low noise & low vibration: lower noise and vibration compared to bevel type motors (avg. 52 ~ 65dB)
3. High strength and long life: increased gear strengths and life by using carburized gears.
4. Light weight & optimization: reduced the installation space using offset method; and reduced the weight of the case and the speed control unit.
Worm gear | Hypoid gear | Note | |
---|---|---|---|
Motor volume(kW) | 0.4 | 0.4 | |
Reduction ratio | 10:1 ~ 20:1 | 10:1 ~ 20:1 | |
Efficiency | 60% | 85% | about 25% difference |
Output Torque (kg-m) | 7.8 | 11.0 | about 25% difference |
Size(mm) Including motor | 416x238x195 | 372x132x118 | about 50% difference |
Weight(kgf) Including motor | 20 | 11 | about 50% difference |
Material | Thickness | Remark |
---|---|---|
AL/Stainless | 1~2mm | dual-press molding, rounded design |
-Manufactured using high-strength Aluminum dual extrusion molding method. High resistancy against strong wind and separable by segment
- Convenient & affordable A/S.
- Round-shaped design improves the overall appearance. WIND LOCK SYSTEM helps to prevents Derailment.
- Encapsulated bearing design prevents the foreign materials damaging the parts and the rust.
BLUE
ORANGE
GREY
MESH
Transparency
Yellow Transparency
Material | Thickness | Breaking strength | Temperature range | Themal conductivity | Remark |
---|---|---|---|---|---|
PVC | 2mm | 150N/M | -30~+80° | 0.10 W/(m*k) | flame retardant (ISO340) |
Customizable to meet customers’ requirements
< Antibacterial, flame-retardant, nonwoven articles double layer structure >
– Top grade materials (SOL Screen Coating, high strength) which is used for boat manufacturing
– No fabric material distortion, no pin-hole, excellent adhesion characteristics
– Surface Treatment/Coating: Fluoride (PVDF), acrylic, PU treatment. Can apply the treatments up to 5 times
You can print the company logo and desired text in various formats.
Controller Description
1. High performance inverter controller specially designed for high speed auto doors
2. Basic, recovery type, Counter-Balance, including all applicable Doors
3. ENCODER / LIMIT TYPE position control can be combined
4. 1HP ~ 3HP can be applied to the motor
5. The person / vehicle STEP 2 that separates the open control
6. The various interlocking devices (air curtain, conveyors, flashing light) and compatibility available
7. The maximum repellent effect as air curtains and air-conditioning settings associated time
8. Damage caused by external controllers to prevent flooding by rainwater inflow and waterproof CASE